-
Precautions for Using Fusion Splicer in Winter
Dec 07 , 2020
For communication workers working outdoors, the working environment in winter is relatively harsh. Rain and snow, windy weather, and foggy weather all bring great challenges to welding. The staff is shivering in the cold outside. The fusion splicer is also prone to failure. Today, I will give you some tips for using the fusion splicer in harsh environments and the points that should be paid attent...
Read More
-
Do you know optical cable identifier?
Dec 11 , 2020
Introduction Optical cable identifier instrument, is based on the principle of optical fiber interference, through optical coherent demodulation to convert the tapping vibration signal of the optical cable into visual and audio signals, so as to accurately find and identify targets in various laying methods Optical cable. The fiber optic cable survey instrument can be used not only for the mainten...
Read More
-
What is the FTTx?
Dec 16 , 2020
FTTx is the abbreviation of “Fiber to the X”, which means “fiber to x”, which is a general term for various fiber-optic communication networks, where X represents the destination of the fiber-optic line. The FTTx network applications in GPON access have the following in common: The data, voice, and video signals of terminal users are sent to ONUs, where the signals are converted into Ethernet pack...
Read More
-
The simple failure analysis and elimination of fusion splicer
Dec 23 , 2020
1. During the splicing process, the fusion splicer displays "fiber not found or the end face of the fiber is untidy". This is mainly caused by the surface of the optical system being contaminated. The protective glass (located under the electrode) should be cleaned with absolute alcohol, and the lens on the fiber cover should be cleaned at the same time. Wait until the alcohol is dry before procee...
Read More
-
What's fiber optic pigtail?
Jan 06 , 2021
A fiber pigtail is a single, short, usually tight-buffered fiber optic cable with a factory-installed connector on one end, and un-terminated fiber on the other end, making the maintenance more conveniently. Fiber optic pigtails are used to terminated fiber optic cables via fusion splicing or mechanical splicing as shown in the picture below. The end of the pigtail is stripped and fusion spli...
Read More
-
What are the commonly used fiber optic tools？
Jan 21 , 2021
The gradual increase in the construction and maintenance of optical cables in the optical communication industry has prompted an increase in the demand for various optical fiber tools. Common optical fiber tools on the market include optical fiber strippers, optical cable strippers, and optical cable cutting shears. The purpose of these tools is also different, are you really familiar with them? K...
Read More
-
Precautions for using VFL
Feb 03 , 2021
Visual Fault Locator are also called VFL, pen-type red light sources, visible light detector, optical fiber fault detectors, optical fiber fault locators, etc. Most of them are used to detect fiber breakpoints. According to their shortest detection distance, they are divided into: 5Km, 10Km, 15Km, 20Km, 25Km, 30Km, 35Km, 40Km, etc. Driven by a constant current source, a stable red light is emitted...
Read More
-
How to clean the end face of optical fiber?
Feb 24 , 2021
Pentype One-Click Fiber Cleaner is loved by many users because of its convenient use. When using, you only need to insert the optical fiber cleaner into the connector, and then gently push it inward. When you hear the "Ka Ta" sound prompt, pull out the cleaner, and the cleaning work is completed. Therefore, it can also be called a one click optical fiber end face cleaner. In order to make it ...
Read More
-
The Introduce of Fiber Optic Microscope
Mar 10 , 2021
Fiber optic microscopes are used to inspect connectors to check the quality of the termination procedure and diagnose problems. A well made connector will have a clean, smooth, polished and scratch free finish. There is not be any signs ofcracks, chips or fiber not even with the ferrule front. The magnification for viewing connectors can be 30 to 400 power. Seikofire sells S620mini video optical f...
Read More
-
The correct use of fiber stripper
Mar 17 , 2021
Professional tools should be used when stripping the coating layer of the optical fiber. The most typical tool is the Fiber Stripper; it can thin the plastic outer layer outside the pigtail, and it can also strip the coating layer of the optical fiber. Pay attention to: 1. When peeling off the coating layer of the optical fiber, there should be no impurities in the small holes of the fiber strippe...
Read More
-
Optical fiber will be the foundation of 5G network
Apr 01 , 2021
With the continuous changes in 5G wireless standards, what measures can network operators take to lay the foundation for 5G transmission networks? The good news is that at least the path of 5G at the physical layer is clear: optical fiber will be the foundation of 5G networks, and centralized RAN (C-RAN) will become the 5G network architecture. C-RAN was introduced through 4G (commercial de...
Read More
-
Daily maintenance of fusion splicer
Apr 09 , 2021
In the fusion state, the optical fiber advancement stops and the machine does not perform fusion operation. The reason is that the V-groove is dirty and must be cleaned. After closing the windproof cover, the optical fiber will not push forward. Reason: 1. The bare optical fiber is placed too far from the electrode or beyond the electrode, please replay the optical fiber. 2. The objective lens has...
Read More
-
Why we need OCID?
Apr 23 , 2021
As demand for optical fiber increases day by day,the numbers of fibers in a single optical cable can be as many as 2096 individual fibers.As more fiber cables are buried underground,it becomes extremely dificult for the telecom engineers and technicians to manage the cables because cables may take different pathways, or be labeled incorrectly. As vast large number of optical cable being deployed b...
Read More
-
OTDR: General Questions
Apr 28 , 2021
Q: What do OTDRs test? A: OTDRs test the overall length, loss and optical return loss of fiber optic cables or networks. Additionally, they detect, locate, identify and measure optical components in installed networks including fusion splices, optical connectors and PON splitters as well as faults such as breaks or tight bends causing high loss. Q: Does it take training to use an OTDR? A: Each OTD...
Read More
-
How to distinguish SM and MM fiber？
May 07 , 2021
According to the transmission mode of light in the fiber, it can be divided into: single-mode fiber and multi-mode fiber. The core diameter of the multimode fiber is 50-62.5μm, the outer diameter of the cladding is 125μm, the core diameter of the single-mode fiber is 8.3μm, and the outer diameter of the cladding is 125μm. The working wavelength of the optical fiber has short wavelength 0.85μm, lon...
Read More
-
NEW Fiber Identifier With VFL Function
Jun 07 , 2021
Upgraded high accuracy fiber identifier S506 integrates VFL and LED lighting function,It is one of the necessary tools for fiber maintenance.Fiber identifier can detect any position of the single mode and multi mode fiber. With the fiber identifier to identify the fiber on the line, you can identify the fiber power and 3 kinds of signal frequencies, and there will be a buzzer sound when identifyin...
Read More
IPv6 network supported
English
русский
español
português
sales@seikofire.com
