-
What is Fusion Splicer And How to Splice Two Fibers?
May 22 , 2020
What is a fiber optical fusion splicer? Fusion splicer is to use high-temperature heat generated by electric arc and melt two optical fibers together at their end faces,to form single long fiber.More precisely, the fiber ends are initially brought in close contact,with a small gap in between. After heating them for a short while such that the surfaces melt, they are pushed together, such that the ...
Read More
-
The Principle and Maintenance of Fiber Cleaver
Jun 09 , 2020
For fiber optics,clean and smooth end face is very important when splicing fiber optic cables.The fiber optic cleaver is a crucial tool for low-loss and low-reflectance fiber optic splices and terminations. The principle of a fiber cleaver 1. Fix fibers Open the body cover and put the striped fiber on the V-groove.Then close the holder cover. 2. Cut the knife mark on the fiber Slip the c...
Read More
-
Fusion Splicer Maintenance how to Clean its V-groove?
Jun 09 , 2020
Fusion splicer is a high precision equipment, it is very import to do the maintenance during daily work. V-groove is a V slot on the ceramic substrate of narrow width, easily to accumulate dust which will make the fiber move instability and cause a bad fusion, therefore, the V groove should be cleaned regularly. The following is the way of cleaning the V-groove
Read More
-
The Classifications of Optical Fiber Fusion Splicers
Jul 24 , 2020
Before the fusion of the optical fiber fusion splicer, according to the material and type of the optical fiber, the key parameters such as the pre-melting main melting current and time and the fiber feeding amount are set. During the welding process, the “V” shaped groove, electrode, objective lens, welding chamber, etc. of the welding machine should be cleaned in time. Observe the presence or abs...
Read More
-
The maintenance and replacement of electrodes for optical fiber fusion splicer
Aug 28 , 2020
The electrode rod is an important part of the welding machine. Discharge welding is completed by the electrode rod. However, many people do not understand that the electrode rod is a consumable and needs to be replaced when it reaches a certain life span. Although the metal itself is hard and will not be worn by external forces, it needs to withstand high temperature discharge for a long time. At ...
Read More
-
Do you know what is fiber optic splicing?
Sep 18 , 2020
Fiber optic cable fusion splicing is a meticulous work, especially in the end face preparation, fusion splicing, coiling and other links. Fiber fusion splicing is to connect two-core fibers through a specific equipment fiber fusion splicer. 1. Preparation before optical fiber fusion splicing First prepare fiber stripper, cutter, fusion splicer, heat-shrinkable tube, alcohol cotton and ...
Read More
-
Cleaning of fusion splicer's microscopes (objective lenses)
Oct 23 , 2020
The fusion splicer uses the image processing system to observe the optical fiber. If the microscopic lens becomes dirty, it will affect the normal optical fiber observation, resulting in poor welding effect. Therefore, the lenses of the two microscopes should be cleaned regularly to keep the microlenses clean and tidy. The specific process is as follows: (1) turn off the power supply of the f...
Read More
-
Optical fiber alignment of optical fiber splicing machine
Nov 20 , 2020
Using optical fiber fusion machine for optical fiber fusion is one of the mainstream methods of optical fiber field termination, so there are many kinds of optical fiber fusion machine in the market, which is dazzling. How to choose a cost-effective optical fiber fusion machine has become a headache for many skilled workers. We know that the alignment accuracy of the optical fiber fusion machine i...
Read More
-
Precautions for Using Fusion Splicer in Winter
Dec 07 , 2020
For communication workers working outdoors, the working environment in winter is relatively harsh. Rain and snow, windy weather, and foggy weather all bring great challenges to welding. The staff is shivering in the cold outside. The fusion splicer is also prone to failure. Today, I will give you some tips for using the fusion splicer in harsh environments and the points that should be paid attent...
Read More
-
The simple failure analysis and elimination of fusion splicer
Dec 23 , 2020
1. During the splicing process, the fusion splicer displays "fiber not found or the end face of the fiber is untidy". This is mainly caused by the surface of the optical system being contaminated. The protective glass (located under the electrode) should be cleaned with absolute alcohol, and the lens on the fiber cover should be cleaned at the same time. Wait until the alcohol is dry before procee...
Read More
-
Daily maintenance of fusion splicer
Apr 09 , 2021
In the fusion state, the optical fiber advancement stops and the machine does not perform fusion operation. The reason is that the V-groove is dirty and must be cleaned. After closing the windproof cover, the optical fiber will not push forward. Reason: 1. The bare optical fiber is placed too far from the electrode or beyond the electrode, please replay the optical fiber. 2. The objective lens has...
Read More
-
ARC Checking and Maintenance of the Splicer
May 21 , 2021
Working with fiber optics takes a delicate hand and some patience. One of the most used pieces of equipment is a fusion splicer. A fusion splicer uses an electric arc to fuse two pieces of optical fiber (glass) together so that light can pass through with no scatter of light or light reflected back (backscatter) by the splice. Fusion splicing helps to reduce loss in your network. Typical loss thro...
Read More
-
What does AUTO mean in splicing mode of optical fiber fusion splicer？
Jun 18 , 2021
AUTO automatically recognizes the fiber type and corrects the discharge parameter mode in real time. SM is a single-mode fiber mode, NZ is a non-zero displacement dispersion fiber mode, and DS is a displacement dispersion fiber mode. Optical fibers for communication are generally SM (single-mode) or MM (multi-mode), of which SM is the majority. SeikoFire S5 optical fiber fusion splicer is mainly u...
Read More
-
Four Basic Steps to Complete a Proper Fusion Splicing
Jul 15 , 2021
Step 1. Preparing the Fibers 1. Strip jacket and remove an adequate amount of jacket, usually 2-3 m, for splicing and dressing the buffer tubes and fibers in the splice closure. Leave the proper amount of strength members to attach the cable to the closure. Refer to the splice closure directions for lengths needed. Clean all water-blocking materials using appropriate cleaners. 2. Remove buffer tub...
Read More
-
Why the fiber end face always appears bad when the fusion splicer is splicing?
Aug 04 , 2021
1. The new end face is contaminated by debris, dust, etc. Solution: Do not let the cut fiber end face touch anything; 2. When cutting the optical fiber, the angle is too large. In this case, it may be a problem with the cleaver blade. Change a blade for an interview, or there may be debris in the fiber groove of the cleaver. Use a sharp object to clean the fiber groove. ； 3. There are gray and dar...
Read More
-
Classification of optical fiber loss.
Aug 13 , 2021
The optical fiber loss can be divided into the inherent loss of the optical fiber and the additional loss caused by the service conditions after the optical fiber is made. The details are as follows: Optical fiber loss can be divided into inherent loss and additional loss. The inherent loss includes scattering loss, absorption loss and the loss caused by the imperfect structure of optical fib...
Read More
IPv6 network supported
English
русский
español
português
sales@seikofire.com
