-
What is Fusion Splicer And How to Splice Two Fibers?
May 22 , 2020
What is a fiber optical fusion splicer? Fusion splicer is to use high-temperature heat generated by electric arc and melt two optical fibers together at their end faces,to form single long fiber.More precisely, the fiber ends are initially brought in close contact,with a small gap in between. After heating them for a short while such that the surfaces melt, they are pushed together, such that the ...
Read More
-
How is the Submarine Cable Laid?
Jun 09 , 2020
The submarine communication cable is a wire wrapped with insulating material and laid on the seabed to complete the telecommunications transmission between countries. The first batch of submarine communication cables were used to supply telegraph communications, and later began to introduce telephone communications and Internet communications. Modern fiber optic cables also used fiber optic skills...
Read More
-
The Principle and Maintenance of Fiber Cleaver
Jun 09 , 2020
For fiber optics,clean and smooth end face is very important when splicing fiber optic cables.The fiber optic cleaver is a crucial tool for low-loss and low-reflectance fiber optic splices and terminations. The principle of a fiber cleaver 1. Fix fibers Open the body cover and put the striped fiber on the V-groove.Then close the holder cover. 2. Cut the knife mark on the fiber Slip the c...
Read More
-
The Classifications of Optical Fiber Fusion Splicers
Jul 24 , 2020
Before the fusion of the optical fiber fusion splicer, according to the material and type of the optical fiber, the key parameters such as the pre-melting main melting current and time and the fiber feeding amount are set. During the welding process, the “V” shaped groove, electrode, objective lens, welding chamber, etc. of the welding machine should be cleaned in time. Observe the presence or abs...
Read More
-
Introduce of Optical Power Meters
Aug 31 , 2020
Introduce of Optical Power Meters An optical power meter (or laser powermeter) is an instrument for the measurement of the optical power (the delivered energy per unit time) in a light beam, for example a laser beam. Typically, it allows for power measurements only with a relatively low bandwidth, and will e.g. display only the average power when receiving a pulse&nbs...
Read More
-
Everything You Need to Know About Fiber Optics Cable
Sep 11 , 2020
In the recent years, fiber optics is steadily replacing copper wires. It is a better and apt means of transmitting communication signals. Today, fiber optics cable span across long distances between local phone systems. In addition, it also serves as the backbone for many networking systems including: Cable TV services University campus Office buildings Industrial plants Electric utility companies...
Read More
-
Do you know what is fiber optic splicing?
Sep 18 , 2020
Fiber optic cable fusion splicing is a meticulous work, especially in the end face preparation, fusion splicing, coiling and other links. Fiber fusion splicing is to connect two-core fibers through a specific equipment fiber fusion splicer. 1. Preparation before optical fiber fusion splicing First prepare fiber stripper, cutter, fusion splicer, heat-shrinkable tube, alcohol cotton and ...
Read More
-
What is the difference between single-mode fiber and multi-mode fiber? Which one to choose?
Sep 21 , 2020
The first is to introduce the difference between multimode fiber and single mode fiber: Multimode fiber The optical signal in multimode fiber propagates through multiple channels; it is usually recommended to be used when the distance is less than miles. The effective distance of multimode fiber from transmitter to receiver is about 5 miles. The usable follow-up is also affected by the type and qu...
Read More
-
The Basic Principles of OTDR
Oct 15 , 2020
OTDR is called Optical Time Domain Reflectometer, which injects narrow light pulses into the fiber end face as a detection signal. When the light pulse propagates along the fiber, the backscattered part of Rayleigh scattering everywhere will continue to return to the incident end of the fiber. When the optical signal encounters a crack, Fresnel reflection will occur, and the back reflected light w...
Read More
-
Cleaning of fusion splicer's microscopes (objective lenses)
Oct 23 , 2020
The fusion splicer uses the image processing system to observe the optical fiber. If the microscopic lens becomes dirty, it will affect the normal optical fiber observation, resulting in poor welding effect. Therefore, the lenses of the two microscopes should be cleaned regularly to keep the microlenses clean and tidy. The specific process is as follows: (1) turn off the power supply of the f...
Read More
-
How To Use Our Fiber Stripper CFS-3?
Oct 30 , 2020
The Operation Steps of Fiber Stripper CFS-3 1.Strip the fiber following steps 1 through 3 below. Step 1 : Insert fiber into the opening of the tool. Step 2 : Close the tool squarely around the fiber. Step 3 : Draw the tool along the fiber using thumb pressure while keeping the tool perpendicular to the fiber. 2.Clean the stripped fiber and terminate connection per connector splice or connector man...
Read More
-
How to Use VFL
Nov 04 , 2020
VFL is very easy to use. The steps to use a VFL are provided as following: Step One: remove the plastic connector covers from both ends of the test fiber cable. Step Two: connect the fiber optic visual fault locator one end of the fiber. Press the tester button and observe that light emanates from the other end of the fiber. This gives a simple indication of the continuity of the fiber link. Step ...
Read More
-
Optical fiber alignment of optical fiber splicing machine
Nov 20 , 2020
Using optical fiber fusion machine for optical fiber fusion is one of the mainstream methods of optical fiber field termination, so there are many kinds of optical fiber fusion machine in the market, which is dazzling. How to choose a cost-effective optical fiber fusion machine has become a headache for many skilled workers. We know that the alignment accuracy of the optical fiber fusion machine i...
Read More
-
The Notes When Using OTDR
Nov 26 , 2020
1. Simple judgment of fiber quality: Under normal circumstances, the slope of the main body of the light curve (single disk or several optical cables) tested by OTDR is basically the same. If the slope of a certain section is large, it indicates that the attenuation of this section is large; if the main body of the curve is of irregular shape, the slope fluctuation is large. Bending or arcing indi...
Read More
-
Do you know optical cable identifier?
Dec 11 , 2020
Introduction Optical cable identifier instrument, is based on the principle of optical fiber interference, through optical coherent demodulation to convert the tapping vibration signal of the optical cable into visual and audio signals, so as to accurately find and identify targets in various laying methods Optical cable. The fiber optic cable survey instrument can be used not only for the mainten...
Read More
-
What is the FTTx?
Dec 16 , 2020
FTTx is the abbreviation of “Fiber to the X”, which means “fiber to x”, which is a general term for various fiber-optic communication networks, where X represents the destination of the fiber-optic line. The FTTx network applications in GPON access have the following in common: The data, voice, and video signals of terminal users are sent to ONUs, where the signals are converted into Ethernet pack...
Read More
IPv6 network supported
English
русский
español
português
sales@seikofire.com
