-
What are the commonly used fiber optic tools？
Jan 21 , 2021
The gradual increase in the construction and maintenance of optical cables in the optical communication industry has prompted an increase in the demand for various optical fiber tools. Common optical fiber tools on the market include optical fiber strippers, optical cable strippers, and optical cable cutting shears. The purpose of these tools is also different, are you really familiar with them? K...
Read More
-
The correct use of fiber stripper
Mar 17 , 2021
Professional tools should be used when stripping the coating layer of the optical fiber. The most typical tool is the Fiber Stripper; it can thin the plastic outer layer outside the pigtail, and it can also strip the coating layer of the optical fiber. Pay attention to: 1. When peeling off the coating layer of the optical fiber, there should be no impurities in the small holes of the fiber strippe...
Read More
-
Daily maintenance of fusion splicer
Apr 09 , 2021
In the fusion state, the optical fiber advancement stops and the machine does not perform fusion operation. The reason is that the V-groove is dirty and must be cleaned. After closing the windproof cover, the optical fiber will not push forward. Reason: 1. The bare optical fiber is placed too far from the electrode or beyond the electrode, please replay the optical fiber. 2. The objective lens has...
Read More
-
ARC Checking and Maintenance of the Splicer
May 21 , 2021
Working with fiber optics takes a delicate hand and some patience. One of the most used pieces of equipment is a fusion splicer. A fusion splicer uses an electric arc to fuse two pieces of optical fiber (glass) together so that light can pass through with no scatter of light or light reflected back (backscatter) by the splice. Fusion splicing helps to reduce loss in your network. Typical loss thro...
Read More
-
What does AUTO mean in splicing mode of optical fiber fusion splicer？
Jun 18 , 2021
AUTO automatically recognizes the fiber type and corrects the discharge parameter mode in real time. SM is a single-mode fiber mode, NZ is a non-zero displacement dispersion fiber mode, and DS is a displacement dispersion fiber mode. Optical fibers for communication are generally SM (single-mode) or MM (multi-mode), of which SM is the majority. SeikoFire S5 optical fiber fusion splicer is mainly u...
Read More
-
Four Basic Steps to Complete a Proper Fusion Splicing
Jul 15 , 2021
Step 1. Preparing the Fibers 1. Strip jacket and remove an adequate amount of jacket, usually 2-3 m, for splicing and dressing the buffer tubes and fibers in the splice closure. Leave the proper amount of strength members to attach the cable to the closure. Refer to the splice closure directions for lengths needed. Clean all water-blocking materials using appropriate cleaners. 2. Remove buffer tub...
Read More
-
Why the fiber end face always appears bad when the fusion splicer is splicing?
Aug 04 , 2021
1. The new end face is contaminated by debris, dust, etc. Solution: Do not let the cut fiber end face touch anything; 2. When cutting the optical fiber, the angle is too large. In this case, it may be a problem with the cleaver blade. Change a blade for an interview, or there may be debris in the fiber groove of the cleaver. Use a sharp object to clean the fiber groove. ； 3. There are gray and dar...
Read More
-
Classification of optical fiber loss.
Aug 13 , 2021
The optical fiber loss can be divided into the inherent loss of the optical fiber and the additional loss caused by the service conditions after the optical fiber is made. The details are as follows: Optical fiber loss can be divided into inherent loss and additional loss. The inherent loss includes scattering loss, absorption loss and the loss caused by the imperfect structure of optical fib...
Read More
-
What can 5G bring to you in the optical communication 700MHz technology industry seminar?
Sep 26 , 2021
Background introduction. China Radio and Television Zeng Qingjun said that 5G NR broadcasting does not change the existing network transmission system, and uses the existing NR channel to enable all 5G terminals to receive 5G digital television, without worrying about traffic and network congestion. What is the 700MHz Technology Industry Application Seminar? With the continuous acceleration of 5G ...
Read More
-
How to solve these six problems encountered in the process of optical fiber fusion splicing?
Sep 29 , 2021
1. There are bubbles or cracks in the contacts during welding This situation may be due to poor fiber cutting, such as the end face is inclined, burrs, or the end face is not clean, and the fiber needs to be cleaned before the splicing operation; there is also a situation that the electrical electrode is aging and the electrode rod needs to be replaced. 2. The welding is too thick or the contact p...
Read More
-
What are reflective and non-reflective events in otdr?
Jan 21 , 2022
1. The height of each point in the OTDR curve represents the backscattered light intensity at that location. When looking at the OTDR curve, you can see that the reflected signal is raised in some places, as if the optical power at the back is stronger than the front, which is impossible. Generally, this situation is the backscattering peak caused by the Fresnel reflection at the splicing, breakin...
Read More
-
Ten reasons for excessive splicing loss of optical fiber
Feb 23 , 2022
1. Choose the wrong optical fiber splicing program; for example, misselect the single-mode splicing program to multi-mode. 2. The cutting angle of the end face of optical fiber is too large. 3. The optical system is dirty, mainly the reflector and objective lens. 4. V-shaped slot dirty, optical fiber pressure foot dirty. 5. The aging of the electrode leads to the weak discharge intensity, and the ...
Read More
-
FTTH network construction mainly provides services.
Mar 11 , 2022
1. Overall planning. With reference to the development requirements of the broadband access network in the Chinese market, and combined with the characteristics of the current GPON products and the specific operation of the current network deployment, it is recommended to adopt the FTTH construction mode, with the ability to provide ultra-high bandwidth for end users, and to bring functional...
Read More
-
What is the difference between fiber patch cords and pigtails?
Apr 01 , 2022
The difference between the two is that the pigtail is used to connect the optical cable and the jumper, and the jumper is to connect the pigtail and the terminal equipment. Optical fiber jumper is a jumper used from equipment to optical fiber cabling link, also known as optical fiber connector, which has a thicker protective layer and is generally used in the connection between optical transceiver...
Read More
-
Working principle of Optical Fiber Fusion splicer.
Apr 12 , 2022
Optical fiber fusion splicer can be said to be an indispensable tool product in the field of communication engineering. for people who have had experience in communication engineering, they must know the operation of the fusion splicer like the back of their hand, but it is such a fiber fusion splicer. do you know how he works? Today we will introduce, if you understand, it may be helpful to the l...
Read More
-
How to reduce the fusion splicing loss?
Apr 28 , 2022
The size of the loss is a very important technical indicator of the optical fiber fusion splicer. The lower the loss, the higher the precision of the machine, which can support longer distance fusion splicing. The more perfect the fusion point, the longer the service life. 1. The fiber cleaver cutting angle of the fiber is very important. At present, most of the optical fiber fusion splicers are f...
Read More
IPv6 network supported
English
русский
español
português
sales@seikofire.com
