-
Why we need OCID?
Apr 23 , 2021
As demand for optical fiber increases day by day,the numbers of fibers in a single optical cable can be as many as 2096 individual fibers.As more fiber cables are buried underground,it becomes extremely dificult for the telecom engineers and technicians to manage the cables because cables may take different pathways, or be labeled incorrectly. As vast large number of optical cable being deployed b...
Read More
-
ARC Checking and Maintenance of the Splicer
May 21 , 2021
Working with fiber optics takes a delicate hand and some patience. One of the most used pieces of equipment is a fusion splicer. A fusion splicer uses an electric arc to fuse two pieces of optical fiber (glass) together so that light can pass through with no scatter of light or light reflected back (backscatter) by the splice. Fusion splicing helps to reduce loss in your network. Typical loss thro...
Read More
-
What does AUTO mean in splicing mode of optical fiber fusion splicer？
Jun 18 , 2021
AUTO automatically recognizes the fiber type and corrects the discharge parameter mode in real time. SM is a single-mode fiber mode, NZ is a non-zero displacement dispersion fiber mode, and DS is a displacement dispersion fiber mode. Optical fibers for communication are generally SM (single-mode) or MM (multi-mode), of which SM is the majority. SeikoFire S5 optical fiber fusion splicer is mainly u...
Read More
-
Four Basic Steps to Complete a Proper Fusion Splicing
Jul 15 , 2021
Step 1. Preparing the Fibers 1. Strip jacket and remove an adequate amount of jacket, usually 2-3 m, for splicing and dressing the buffer tubes and fibers in the splice closure. Leave the proper amount of strength members to attach the cable to the closure. Refer to the splice closure directions for lengths needed. Clean all water-blocking materials using appropriate cleaners. 2. Remove buffer tub...
Read More
-
Why can't the OTDR test, how to test?
Jul 26 , 2021
For our communication, OTDR is the equipment that we usually have to get in touch with, so analyzing OTDR and detecting faults is a skill we need to learn So what aspects should we start with if the OTDR test fails? Next, the editor will take you to learn more about how to detect OTDR problems. Especially when it can't be tested. 1. The optical port is not plugged in properly. Our OTDR optical por...
Read More
-
Why the fiber end face always appears bad when the fusion splicer is splicing?
Aug 04 , 2021
1. The new end face is contaminated by debris, dust, etc. Solution: Do not let the cut fiber end face touch anything; 2. When cutting the optical fiber, the angle is too large. In this case, it may be a problem with the cleaver blade. Change a blade for an interview, or there may be debris in the fiber groove of the cleaver. Use a sharp object to clean the fiber groove. ； 3. There are gray and dar...
Read More
-
Classification of optical fiber loss.
Aug 13 , 2021
The optical fiber loss can be divided into the inherent loss of the optical fiber and the additional loss caused by the service conditions after the optical fiber is made. The details are as follows: Optical fiber loss can be divided into inherent loss and additional loss. The inherent loss includes scattering loss, absorption loss and the loss caused by the imperfect structure of optical fib...
Read More
-
What is OTDR Blind Area?
Aug 26 , 2021
Why does the blind area come up? The OTDR produces a blind area because the OTDR's detector is temporarily "blinded" by the high intensity Fresnel reflection light (mainly caused by the air gap between the OTDR connections). When the high intensity reflection is produced, the power of the photodiode is more than 4000 times higher than the backscatter power. Thus, the reflected light signal receive...
Read More
-
What can 5G bring to you in the optical communication 700MHz technology industry seminar?
Sep 26 , 2021
Background introduction. China Radio and Television Zeng Qingjun said that 5G NR broadcasting does not change the existing network transmission system, and uses the existing NR channel to enable all 5G terminals to receive 5G digital television, without worrying about traffic and network congestion. What is the 700MHz Technology Industry Application Seminar? With the continuous acceleration of 5G ...
Read More
-
How to solve these six problems encountered in the process of optical fiber fusion splicing?
Sep 29 , 2021
1. There are bubbles or cracks in the contacts during welding This situation may be due to poor fiber cutting, such as the end face is inclined, burrs, or the end face is not clean, and the fiber needs to be cleaned before the splicing operation; there is also a situation that the electrical electrode is aging and the electrode rod needs to be replaced. 2. The welding is too thick or the contact p...
Read More
-
Ten reasons for excessive splicing loss of optical fiber
Feb 23 , 2022
1. Choose the wrong optical fiber splicing program; for example, misselect the single-mode splicing program to multi-mode. 2. The cutting angle of the end face of optical fiber is too large. 3. The optical system is dirty, mainly the reflector and objective lens. 4. V-shaped slot dirty, optical fiber pressure foot dirty. 5. The aging of the electrode leads to the weak discharge intensity, and the ...
Read More
-
Working principle of Optical Fiber Fusion splicer.
Apr 12 , 2022
Optical fiber fusion splicer can be said to be an indispensable tool product in the field of communication engineering. for people who have had experience in communication engineering, they must know the operation of the fusion splicer like the back of their hand, but it is such a fiber fusion splicer. do you know how he works? Today we will introduce, if you understand, it may be helpful to the l...
Read More
-
How to reduce the fusion splicing loss?
Apr 28 , 2022
The size of the loss is a very important technical indicator of the optical fiber fusion splicer. The lower the loss, the higher the precision of the machine, which can support longer distance fusion splicing. The more perfect the fusion point, the longer the service life. 1. The fiber cleaver cutting angle of the fiber is very important. At present, most of the optical fiber fusion splicers are f...
Read More
-
The use of Seikofire fiber fusion splicer GPS function
May 13 , 2022
The use of Seikofire fiber fusion splicer GPS function. 1 download and install "Aika Life" APP on the mobile terminal. 2 Open the "Aika Life" APP, enter the ID address of GPS, enter the original password 123456, and click "Log in" 3 Click "Real-time tracking" to view the location of the device, the location of the mobile terminal and the device to. The straight line of the mobile phone terminal. 4...
Read More
-
OTDR test with light
May 24 , 2022
What is OTDR test with light? When testing with the wavelengths of 1310nm, 1490nm and 1550nm of common OTDR, it is necessary to require that there is no communication optical signal in the line under test. Forcing the test with light will burn out the internal detector of the OTDR. With light test, the OTDR can still complete the test without interrupting the signal light in the line during the te...
Read More
-
Introduction of Bluetooth connection of CT50 Fiber Cleaver
Jun 02 , 2022
CT50 fiber cleaver, as a sign of Fujikura, this cutter has a rare Bluetooth function. CT50's Bluetooth can connect the Fujikura fusion machine to the Fujikura phone APP "Splice +". The only Bluetooth-related function of the CT50 body is the switch Bluetooth, but after establishing a wireless connection with the welder or smartphone, you can use the welder or smartphone to change the settings. In o...
Read More
IPv6 network supported
English
русский
español
português
sales@seikofire.com
